GC TOOLS
IN STOCK AT
MARSH ELECTRONICS
SOLDER AID TOOLS
ELECTRONIC TOOLS
PLIERS
CUTTERS
TWEEZERS
SCISSOR TWEEZERS
SCREWDRIVERS
WIRE TOOLS
TELEVISION TOOLS
SPECIALTY TOOLS
SOLDER AID TOOLS
12-4116 ANTI-STATIC IC INSERTION TOOL $10.93
For all popular DIP ICs. Narrow design permits insertion on crowded boards. Tough plastic plated with metallic (conductive) coating to prevent ESD problems. 14-16 pin.
12-4127 ANTI-STATIC 8-28 PIN IC EXTRACTOR/INSERTION KIT $4.95
Kit contains one 8-28 pin extractor & one 8-28 pin inserter.
12-4128 ANTI-STATIC IC INSERTION TOOL CUTTERS & STRIPPERS $13.92
Same as 12-4116 except for 24-28 pin.
12-4140 ANTI-STATIC IC INSERTION TOOL $13.92
Same as 12-4116 except for 36-40 pin.
12-4612 - 8-24 PIN GROUNDED DIP IC EXTRACTOR $19.35
Pin extractor with conductive finish & ground strap connection point.Fits all LSI, MSI & SSI devices.
9077-1 ALUMINUM HEAT SINK $1.05
Fits short leads such as transistors mounted close to PC boards.
H3-388 ALUMINUM HEAT SINK $2.02
Protects heat-sensitive components such as semiconductors. Will absorb maximum heat.
12-2150* WRIGGLETฎ DESOLDERING TOOL & LEAD FORMER $3.07
For removing wires, leads, components from circuit boards while desoldering. One end has hole for fitting over wires & wiggling them loose. Opposite end has slotted curved head for prying them up. Aluminum construction with pocket clip. 3 3/4 long.
12-2157 SOLDER POPPER SOLDER TOOL $36.42
3-wire grounded combination of snap-vacuum solder removal tool with a soldering iron for fast operation. Replaceable tip.
12-2160 REPLACEMENT TIP FOR SOLDER POPPER $3.21
200GX-25W SOLDERING IRON $18.25
25 watt soldering iron.
9476 ANGLE REAMER & FORKED TIP $3.635
3/4 stainless steel tool with wood handle.
9486* STRAIGHT REAMER & FORKED TIP $3.63
7 1/2 stainless steel tool with wood handle.
9488 HEAVY DUTY BRUSH & FORKED TIP $3.63
7 1/2 long tool with wood handle.
9094 BRUSH & SCRAPER KIT $3.44
Fine stainless steel brush & hardened steel scraper for solder aid. 8 long with plastic handle.
ELECTRONIC TOOLS
12-1709* 4 STAINLESS STEEL POCKET SLIDE CALIPER $16.47
Inside & outside grading etched in millimeters & 16ths graduations. Decimal equivalents table on back.
12-1712* FIBERGLASS REINFORCED PLASTIC CALIPER $20.81
Graduated in 16ths & 1.0mm with 5.25 capacity. Outside, inside & depth measurements. Slide lock for gauging & transferring measurements. Roller for one hand measuring adjustments. Made in Switzerland.
12-1716 - 6 STAINLESS STEEL FLEXIBLE RULER $3.78
With etched graduations in 32nds & 64ths. 15/32 wide. Decimal equivalents etched on back. With pocket clip.
PLIERS
12-200 Palm grip, flush cut w/spring $19.87
12-216 Palm grip, needle-nose w/spring $16.80
12-7311 5 extra long chain nose $12.05
12-7312 5 extra long bent nose $12.05
12-7313 6extra long bent nose $12.05
12-7314 5.75 needle nose $12.05
12-7315 4.75 long nose w/side cutter $12.05
12-7333 6 long nose serrated $13.43
SCISSOR TWEEZERS
7976 5 long, straight jaw $9.28
7977 6 long, straight jaw $10.61
7978 5 long, curved jaw $9.28
7979 6 long, curved jaw $10.61
CUTTERS
12-7321 4.5 oval head, semi-flush cut $13.43
12-7322 5 oval head, semi-flush cut $13.43
12-7323 4.5 oval head, flush cut $13.43
12-7324 5 oval head, flush cut $13.43
12-7330 4.5 flush tip $13.93
TWEEZERS
7992 4 5/8 long, beveled points $11.90
7995 4.5 long, curved points $ 4.35
SCREWDRIVERS
33828 6-IN-ONE SCREWDRIVER $3.99 (Not pictured.)
8988 FIBERGLASS SCREWDRIVER $3.02
Long-reach slotted screwdriverplastic handle. 14 3/8 total length.
9294 FIBERGLASS SCREWDRIVER $3.02
Double ended extra long screwdriver. 16 total length. (Not pictured.)
WIRE TOOLS
12-463 IDC CRIMP TOOL $22.85
For crimping IDC connectors onto flat ribbon cable. Works with card edge, D-sub, Centronics & other connectors. All steel with cushion grips.
766-K WIRE STRIPPING KIT $39.15
Wire stripping kit: stripper, 3 blades (14-30 AWG wire & RG-58 & RG-59 coax).
12-600 MANUAL WIRE WRAP TOOL $33.25
Wraps 30 AWG wire onto .025 wire wrap posts.
12-603 DUAL WIRE WRAP TOOL $47.51
Strips, wraps & unwraps 22 & 24AWG solid hookup wire. Fits over .045 square posts.
WIRE WRAP IN STOCK
50 spools of silver plated, solid 30AWG KYNARฎ wire.
12-630 Blue & 12-632 Yellow $6.52
12-634 White & 12-636 Red $6.20
TELEVISION TOOLS
9300 HEX ALIGNMENT TOOL $1.72
Double-sided hex tool 5 long.
9440 DOUBLE ENDED TOOL $1.05
Square & hex end tool. 5 1/6 long.
12-2018 PUSH/PULL SPRING HOOK $3.82
8 combination push/pull/lifter tool for manipulating drive belts & springs. Hook on one end, S on the other.
8284 MAGNA TUNING TOOL $1.25
0.100 hex, with flat screwdriver tip (.027 thick, .080 wide), 7/32 long, undercut shaft to reach bottom slugs in coils. 5 1/8 total length.
8454 UNIVERSAL COLOR TV ALIGNMENT TOOL KIT $6.18
5 pc. set including the Extend-it to make long reach aligners out of each tool. In plastic pouch.
9296* DOUBLE SIDED HEX END TOOL $2.07
Hex 5/64, 1/4 long hex, 0.096 dia. shaft; 3/8 long hex; undercut shaft, 11 long.
8282 HEX-SCREWDRIVER COMBO $1.67
Material: Delrin, Hex 0.100 Screwdriver (plastic) 1/8 blade; 1/4 long hex, undercut (0.095 dia.) shaft to reach bottom slugs in coils. 5 7/16 long.
9317 DEGAUSSING COIL $43.89
Professional high-power degaussing coil eliminates magnetic fields in CRT TV picture tubes or computer monitors. 8 cord. UL approved.
SPECIALTY TOOLS
9337 BURNISHING TOOL $1.12
Fineline, 0.120 wide, for small & miniature components.
9338 BURNISHING TOOL $1.22align="left"
Standard, .0250 wide for medium & large contact points. (Not pictured.)
12-472 CABLE TIE GUN $13.88
User controls tension & cuts tie with 180ฐ rotation of tool. Molded plastic.
12-047 SNAP LOCK SCREW STARTER $9.93
Double ended Screw Starter for Phillips & standard slotted screws. Cam action holds screw straight & firm. For most screw sizes up to 1/4. 9 long.
12-040 TAPER REAMER $19.45
For work on chassis or cabinets. Start with 1/8 or larger hole & enlarge to required size. Will also remove burrs. Tapers to 13/16.
5089 FLEXIBLE PICK-UP TOOL $3.91
Mechanical fingers pick up pieces & parts dropped into inaccessible places; holds to start screws, nuts & bolts. 24 long.
9124 POCKET HEX KEY WRENCH SET $3.64
6 wrenches, 0.50 to 3/16 in steel case.
5070 SPLINE KEY WRENCH KIT $6.56
Kit of the 9 most popular size metric hex wrenches: 0.9 mm to 3.2mm sizes. Tempered steel in plastic pouch.
806 NIBBLING TOOL $15.45
Deluxe with spring operated stripper.
12-051 DOUBLE HAND HOLDER $7.16
Six ball joints permit movement to the exact angle required for hands-free operation. Tightened (locked in place) by thumb screw. Alligator clips adjustable to any position, with heavy base that prevents tipping.
* All * items are limited to current inventory. Items shown on this page represent only our stocking items.
If you don't find what you are looking for, please give us a call.
Prices subject to change without notice.
FastCounter by bCentral
Home | About Us | Line Card | Product Index | Services | News
Marsh Electronics, Inc.
N1042 Tower View Drive • Greenville, WI 54942
(920) 757-0800 • (800) 877-8919 • Fax (920) 757-0804
Questions? e-mail us.